Abbreviations

Download list in PDF

top a b c d e f g h i j k l m n o p q r s t u v w x y z
#
  • #
    Setting of setpoints (with this character in front of them) is shared between controllers via intercontroller CAN2
AD
  • ADN
    Archive Drive Nano
AF
  • AFR
    Air Fuel Ratio - method of control of lean burn gas engines
  • AFS
    AFR algorithm for stoichiometric gas engines
AG
  • AG
    AirGate - connection technology to make connecting a ComAp controller to the internet as simple as possible
AH
  • AHI
    Alarmlist & History Indication - protection type (see InteliGen/InteliSys Reference Guide for details)
AI
  • AI
    Analog Input
  • AIC
    InteliCompact NT archive file
  • AID
    Archive ID-DCU
  • AIL
    InteliLite and InteliLite NT archive file
  • AIM
    Archive ID-Mobile
  • AIP
    Archive file InteliPro
AL
  • ALI
    Alarmlist Indication - protection type (see InteliGen/InteliSys Reference Guide for details)
AM
  • AMF
    Auto Mains Failure (controller starts automatically on mains failure)
AN
  • ANT
    IG/IS-NT archive file (contain setpoints, values, history and configuration saved from the particular controller)
AO
  • AO
    Analog Output
AS
  • AS
    All Speed application in ID-DCU and ID-Mobile controllers
  • AST
    Archive Set - file created by InteliMonitor, contain links to archives from all active gen-sets of the site which were saved at the same time
AT
  • ATS
    Automatic Transfer Switch (switches load to supplied bus (by mains or generators))
AV
  • AVR
    Automatic Voltage Regulator
BB
  • BB
    Base Box - controller unit mounted inside of switchboard (without built-in display)
BF
  • BF
    BiFuel - engine operation using combination of both diesel and gas
BI
  • BI
    Binary Input
Bl
  • Bld
    Baseload - gen-set power control mode which keeps constant power supply to the load
BO
  • BO
    Binary Output
  • BOC
    Breaker Open & Cool-down - protection type (see InteliGen/InteliSys Reference Guide for details)
BT
  • BTB
    Bus-Tie Breaker
C/
  • C/O
    Close/Open
C0
  • C0
    awdwd
CA
  • CAN1
    CAN bus for ComAp extension modules (e.g. IGS-PTM) and engine ECU connection (also called peripheral CAN bus)
  • CAN2
    CAN bus for communication between ComAp controllers and communication modules connection (e.g. I-LB+) (also called intercontroller CAN bus)
CB
  • CB
    Circuit Breaker
Cf
  • Cfg
    Controller configuration
CH
  • CHP
    Combined Heat & Power - cogeneration application, usually with a gas engine
CO
  • COX
    Application for Complex Systems where actions are taken by a PLC and controller only follows orders => needs an external driver (cox)
CT
  • CT
    Current Transformer
DC
  • DC
    DriveConfig - PC software for configuration of ID controllers
DD
  • DDE
    Dynamic Data Exchange (DDE server - communication server for most ComAp controllers)
DE
  • DE
    DriveEdit - PC software for ID-Nano configuration
  • Del
    Delay
  • Derating
    Controled reduction of gen-set(s) power based on relevant value, e.g. temperature
DH
  • DHCP
    Dynamic Host Configuration Protocol - network protocol used to configure devices that are connected to a network (known as hosts) so they can communicate on that network using the Internet Protocol (IP)
DI
  • DISTBIN
    DISTributed Binary INPuts - virtual module for receiving binary signals from other IG/IS-NT controllers on CAN bus (supported from v.3.0)
  • DISTBOUT
    DISTributed Binary OUTputs - virtual module for sending binary signals to other IG/IS-NT controllers on CAN bus (supported from v.3.0)
DM
  • DM
    DriveMonitor - PC software for monitoring of InteliDrive controllers
DN
  • DNC
    ID-Nano import package
  • DNF
    ID-Nano Firmware
  • DNS
    Domain Name System - hierarchical distributed naming system for computers, services, or any resource connected to the internet or a private network
DT
  • DT-KIT
    Input/Output Simulator for InteliDrive Family Controllers
E
  • E
    Electric protection - protection type (see InteliGen/InteliSys Reference Guide for details)
EC
  • ECU
    Engine Electronic Control Unit
EF
  • EFC
    Earth Fault Current
  • EFCPM
    Earth Fault Current Protection Module
  • EFI
    Electronic Fuel Injection
EP
  • EP
    Electronic Potentiometer
ES
  • ESC
    Coded Engine Specific File
  • ESF
    Engine Specific File - defines inputs and outputs for controller communication with ECU (part of ECU list)
  • ESL
    Engine Specific List - list of electronic engines supported by particular controller (part of ECU list)
FD
  • FD
    Feedback
  • FDR
    Feeder application for IM-NT controller
Fl
  • Fls
    Fail Sensor
FM
  • FMI
    Failure Mode Identifier
Fo
  • Forward Synchronisation
    Synchronisation of unloaded gen-set to mains (GCB closing process)
FP
  • FPC
    Fire Pump Controller
FV
  • FV
    Force Value - function which enables to change setpoint value by activating/deactivating a binary input
GC
  • GC
    Graphical Characters - controller option for additional support of one "graphical" language: eg Japanese, Chinese etc.
  • GC
    GenConfig - PC tool for configuration of IG/IS-NT controllers
  • GCB
    Generator Circuit Breaker
Ge
  • GeCon
    GEnerator CONtroller - software modification of IG/IS-NT controller for control of generator part of gen-set only
GL
  • GL
    Gen-set Loaded
HS
  • HST
    History record - protection type (see InteliGen/InteliSys Reference Guide for details)
IA
  • IA-NT
    InteliATS New Technology automatic transfer switch controller
I-
  • I-AOUT8
    Extension module with 8 AO for IG/IS-NT and ID controllers
IB
  • IB
    Internet Bridge
  • IBF-2
    Bi-Fuel control system package which enables 4 stroke diesel engines, generating sets or pumps to operate on Bi-fuel/dual-fuel (for max. 6 cylinders engines)
  • IBF-20
    Bi-Fuel control system package which enables 4 stroke diesel engines, generating sets or pumps to operate on Bi-fuel/dual-fuel (for max. 20 cylinders engines)
  • IBF-CU-R
    Bi-Fuel Railway firmware for ID-Mobile
  • IB-Lite
    Communication plug-in module with Ethernet 10/100 Mbit interface in RJ45 connector for IL-NT, IA-NT, IC-NT and ID-Lite controllers
  • IB-NT
    Communication Module with Cellular/Ethernet Connection for IC-NT, IG/IS-NT and ID controllers
I-
  • I-CB
    Communication Bridge - interfaces IS, IG/IS-NT, ID controllers and nonstandard engine ECU
IC
  • ICHG
    InteliCharger - automatic battery charger
  • IC-NT
    InteliCompact NT gen-set controller
  • IC-NT CT-BIO7
    Hybrid plug-in extension module with 1 current input and 7 binary inputs/outputs
I-
  • I-CR
    CAN Repeater module - Intercontroller CAN bus extension module
ID
  • ID
    InteliDrive controller
  • ID-BF
    InteliDrive controller for Bi-Fuel applications
  • IDC
    Import package for DriveConfig
  • ID-CCU
    InteliDrive Compressor Control Unit
  • ID-COM
    Communication module for multiple engine installations, remote displays and redundancy communication for ID controllers
  • ID-DCU
    InteliDrive engine control unit
  • ID-DFM
    Dual Fuel Module for ID-BF controller
  • ID-EM
    InteliDrive Lite Electric Motor controller
  • ID-FLX-DC
    InteliDrive Lite Direct Current controler
  • ID-FLX-FPC
    InteliDrive Lite Fire Pump Controller
  • ID-FLX-IPC
    InteliDrive Lite Irrigation Pump Controller
  • ID-FLX-Lite
    InteliDrive Lite engine controller
  • ID-Lite
    Former version ID-Lite engine controller
  • ID-Mobile
    Engine controller with IP67 protection
  • ID-Mobile Logger
    Engine data logger
  • IDMT
    Inverse Definite Minimum Time - protection which trips the sooner the higher value is measured (e.g. current, load), the dependence is hyperbolic
  • ID-Nano
    InteliDrive Nano - a small engine controller
  • ID-Nano-CC
    InteliDrive Nano Compressor Controller - Small Compressor Controller
  • ID-RPU
    Redundant Protection Unit for ID-DCU-Marine controller
  • ID-SCM
    InteliDrive Speed Control Module - Speed Control Module for InteliDrive controllers
  • ID-SCM1
    InteliDrive Speed Control Module - Speed Control Module for InteliDrive controllers (cost effective version)
IG
  • IG-AVRi
    InteliGen Automatic Voltage Regulator interface
  • IG-AVRi TRANS/LV
    Low voltage transformer for IG Automatic Voltage Regulator interface
  • IGC
    IG/IS-NT firmware upgrade package
  • IG-EE
    InteliGen for Electronic Engines (HWoptimized for connection to an engine equipped with ECU)
  • IG-EEC
    InteliGen EE controller with extended communication possibilities + switchable sensing ranges of AC voltages and currents
  • IG-IB
    IG-Internet Bridge - for internet/ethernet communication
  • IG-IOM
    Extension module with 8 BI/BO, 4 AI and 1 AO for IL-NT, IC-NT and InteliPro controllers
  • IGL-RA15
    Indication panel with LEDs signalizing state of 15 BO
  • IG-MTU
    Mains Transformer Unit
  • IG-NT
    InteliGen NT gen-set controller
  • IG-NT-BB
    InteliGen New Technology BaseBox gen-set controller
  • IG-NTC
    InteliGen New Technology controller with extended communication possibilities + switchable sensing ranges of AC voltages and currents
  • IG-NTC-BB
    InteliGen New Technology BaseBox controller with extended communication possibilities + switchable sensing ranges of AC voltages and currents
  • IGS-NT-LSM+PMS
    Dongle for InteliGen and InteliSys controllers to enable Load Sharing and VAr sharing control loops and PMS
  • IGS-PTM
    Extension module with 8 BI/BO, 4 AI and 1 AO
I-
  • I-LB+
    Local Bridge – communication module for direct and modem monitoring and control of multiple gen-sets
  • I-LBA
    Low Battery Adaptor
IL
  • IL-NT
    InteliLite New Technology gen-set controller
  • IL-NT GPRS
    Communication plug-in module with GSM/GPRS modem for IL-NT, IC-NT and ID-Lite controllers
  • IL-NT RS232
    Communication plug-in module with RS232 port for IL-NT, IA-NT, IC-NT and ID-Lite controllers
  • IL-NT RS232-485
    Communication plug-in module with RS232 and RS485 ports for IL-NT, IANT, IC-NT and ID-Lite controllers
  • IL-NT S-USB
    Service communication plug-in module with USB slave port for IL-NT, IANT, IC-NT and ID-Lite controllers
  • IL-NT-AIO
    Extension plug-in module with 4 analog inputs and 1 analog output for ID-FLX-Lite family controllers
  • IL-NT-AOUT8
    Extension plug-in module with 8 PWM open collector type outputs for ILNT, IA-NT, IC-NT and ID-Lite controllers
  • IL-NT-BIO8
    Extension plug-in module with 8 binary inputs/outputs for IL-NT, IA-NT, IC-NT and ID-Lite controllers
  • IL-NT-IO1
    Extension plug-in module with 4 analog outputs and 4 binary inputs for ID-FLX-Lite family controllers
IM
  • IM-NT
    InteliMains New Technology - Mains supervision controller; the same controller with a different SW configuration can work as a bus-tie synchronizer
  • IM-NT-BB
    InteliMains New Technology BaseBox - Mains supervision controller
  • IM-NTC-BB
    InteliMains New Technology BaseBox - Mains supervision controller with extended communication options
IN
  • IN-NT
    InteliNano New Technology gen-set controller
IP
  • IP
    Internet Protocol
I-
  • I-RB
    Relay Board
IS
  • IS-AIN8
    Extension module with 8 AI
  • IS-AIN8TC
    Extension module with 8 AI for thermocouple measurements
  • IS-BIN8/16
    Extension module with 8 BO and 16 BI.
  • IS-NT
    InteliSys New technology gen-set controller
  • IS-NT-BB
    InteliSys New Technology Basic Box (without display) - classic line
  • IS-NTC-BB
    InteliSys New Technology Basic Box (without display) - new line
IV
  • IV17T
    InteliVision 17Touch - 17" color display for IG/IS-NT and ID controllers
  • IV5
    InteliVision 5 - 5,7" color display for IG/IS-NT controllers
  • IV5 CAN
    InteliVision 5 - 5,7" color display for ID controllers
  • IV5 CAN BL
    InteliVision 5 - 5,7" color display for ID controllers with backlit buttons
  • IV5 RD
    InteliVision 5 Remote Display - 5,7" color display for IG/IS-NT controllers for remote connection up to 1km
  • IV8
    InteliVision 8 - 8" color display for IG/IS-NT and ID controllers
KW
  • KWP2000
    Key Word Protocol of Scania S6 unit (for engine diagnostics)
LA
  • LAI
    Logical Analog Inputs (card in GenConfig which is used to assign source signal to controller Logical Analog Input functions, e.g. Oil press)
LB
  • LBI
    Logical Binary Inputs (card in GenConfig which is used to assign source signal to controller Logical Binary Input functions, e.g. Sys Start/Stop)
LC
  • LChr
    Load Character - IG/IS-NT history column name
LD
  • LDE
    Line Diagram Editor - SCADA editor in InteliMonitor
  • LDS
    Load Demand Swap - automatic start and stop of different sized gen-sets within a group based on actual load and belonging to predefined power bands
  • LdShed
    Load shedding - disconnecting of unessential load after mains fail to enable start of of gen-sets
Lo
  • LoP
    Low Power - protection type, causes reduction of the required gen-set load to the Min Power PtM during parallel-to-mains operation or local baseload operation
LS
  • LS / LdSharing
    Load Sharing - analog load sharing line to interconnect gen-sets on site (for island parallel or mains parallel operation of multiple gen-sets); IG/IS/IM-NT controllers use digital Load Sharing via the CAN2 bus
  • LSM
    Load SharingModule
LT
  • LT
    Option for Low Temperature modification (display equipped with heating foil)
MC
  • MCB
    Mains Circuit Breaker
  • MC-NT
    Mains Compact New Technology controller
MG
  • MGCB
    Master Generator Circuit Breaker (sometimes used with multiple gen-sets in island parallel or mains parallel operation)
MI
  • MINT
    Multiple application with INTernal control loops - for multiple gen-sets in island parallel or mains parallel operation; Load Sharing and VAr Sharing controlled internally; PMS available
MP
  • MP
    Mains Protection
MR
  • MRS
    Manual and Remote Start
Mu
  • MultIslOp
    Multiple Island Operation (MCB is opened, GCB’s are closed)
  • MultParOp
    Multiple Parallel Operation (MCB is closed, GCB’s are closed)
MV
  • MVS
    Mains Vector Shift - IG/IS-NT history column name
NC
  • NCB
    Neutral Circuit Breaker
NP
  • NPU
    Mains protection relay (voltage, frequency, vector shift protections)
OC
  • OC
    Occurrence Count (number of fault occurrances transmitted in diagnostic frame from ECU)
Of
  • OfL
    Off load - protection type (see application manual for details)
Pe
  • Peak shaving
    Supply of part of the load by gen-sets while import from the Mains is higher than preadjusted limit, prevents excess of Mains import limit during periods with high consumption
PF
  • PF
    Power Factor
PG
  • PGN
    Parameter Group Number (refer to SAE J1939-71)
PL
  • PLC
    Programmable Logic Controller - PLC functions available in IG/IS-NT and ID controllers
PM
  • PMS
    Power Management System - ensures optimization of running gen-sets on sites with multiple gen-sets; based on kW/kVA spinning reserve or on relative (%) load; no-master system ensures high reliability
PS
  • PSC
    Power Station Controller - SW branch for IG/IS-NT controllers dedicated to control and monitoring of power stations
PT
  • PT
    Potential Transformer
PW
  • PWM
    Pulse-Width Modulation
Re
  • Reverse synchronisation
    Synchronisation of loaded genset to mains (MCB closing process)
RO
  • ROCOF
    Rate of Change of Frequency - Mains protection
RT
  • RTC
    Real Time Clock
SC
  • SCADA
    Supervisory Control and Data Acquisition systém
SD
  • SD
    Shutdown - protection type (see InteliGen/InteliSys Reference Guide for details)
SG
  • SG
    Speed Governor
SH
  • SHAIN
    Shared (virtual) Analog INput module
  • SHAOUT
    Shared (virtual) Analog OUTput module
  • SHBIN
    SHared (virtual) Binary INput module
  • SHBOUT
    SHared (virtual) Binary OUTput module
SL
  • SLD
    Single Line Diagram - SCADA drawing created in InteliMonitor
SM
  • SMTP
    Simple Mail Transfer Protocol - an Internet standard for electronic mail (e-mail) transmission across Internet Protocol (IP) networks
SN
  • SNMP
    Simple Network Management Protocol - an "Internet-standard protocol for managing devices on IP networks"
So
  • Soft load
    Generator soft loading according to Load ramp loop setting
  • Soft unload
    Generator soft unloading according to Load ramp loop setting
SP
  • SPI
    Single Parallel Island application - for single gen-sets in parallel with mains or in island operation; suitable for CHP applications; no MCB control
  • SPM
    Single Prime Mover application - for single gen-sets without mains
  • SPN
    Suspect Parameter Number (refer to SAE J1939-71)
  • SPtM
    Single Parallel to Mains application - for single gen-sets in parallel with mains or in island operation, with AMF support; bothMCB and GCB controlled
SR
  • SRO
    Speed Regulation Output
SS
  • SS
    Single Speed application in ID-DCU and ID-Mobile controllers
  • SSB
    Single Stand-By application - for single gen-sets with mains and break transfer to mains
ST
  • STP
    Slow stop - protection type
VB
  • VBOUT
    Virtual Binary Outputs (ID-DCU, ID-Mobile)
VP
  • VPIO
    Virtual periphery I/O module – internal “SWwires” linking binary outputs to inputs
VR
  • VRO
    Voltage Regulation Output
VS
  • VS
    VAr Sharing - ensures VAr sharing between gen-sets on site via the CAN2 bus (for island parallel or mains parallel operation of multiple gen-sets)
VT
  • VT
    Voltage Transformer
WR
  • WRN
    Warning
WS
  • WSUP
    WebSupervisor - cloud based system for monitoring and controlling of ComAp controllers through web
ZS
  • ZST
    Zipped Archive Set - file created by InteliMonitor, can be used for sending of complete archive sets to the ComAp technical support